Hammond River Brewing

Post by **mr x** » Tue Aug 06, 2013 5:29 pm

They look like shiney soldiers, ready for battle, lol.

Sent from Tapatalk 2, a prick of a company.

GAM · Post by **GAM** » Tue Aug 06, 2013 5:50 pm

I take back my "cardboard" comment.

Sandy

jeffsmith · Post by **jeffsmith** » Tue Aug 06, 2013 6:32 pm

Sweeeeet…

Tony L · Post by **Tony L** » Tue Aug 06, 2013 6:57 pm

I'll echo Jeff.... Sweeeet

Post by **LeafMan66_67** » Tue Aug 06, 2013 7:16 pm

Nice!

erslar00 · Post by **erslar00** » Tue Aug 06, 2013 7:26 pm

WoW!!! Impressive...

GuingesRock · Post by **GuingesRock** » Tue Aug 06, 2013 7:52 pm

Really really nice. Looks like you will be busy, but maybe later...would you be able to say what they all are, from left to right please. I'm only really sure about the middle two, and maybe the one on the left is a boiler. Holding tanks there? No mash tun there right? or wrong? Did you order them in from the States?

JohnnyMac · Post by **JohnnyMac** » Tue Aug 06, 2013 8:51 pm

Looks awesome! Nothing like the look of brand new stainless steel....

canuck · Post by **canuck** » Tue Aug 06, 2013 9:00 pm

GuingesRock wrote:Really really nice. Looks like you will be busy, but maybe later...would you be able to say what they all are, from left to right please. I'm only really sure about the middle two, and maybe the one on the left is a boiler. Holding tanks there? No mash tun there right? or wrong? Did you order them in from the States?

From left to right....Brite Tank, Mash Tun, Hopback, Fermenter, Fermenter, Hot Liquor Tank, Boil Kettle. I ordered all of this from Stout Tanks & Kettles in Portland, OR.

GuingesRock · Post by **GuingesRock** » Wed Aug 07, 2013 6:40 am

canuck wrote:
GuingesRock wrote:Really really nice. Looks like you will be busy, but maybe later...would you be able to say what they all are, from left to right please. I'm only really sure about the middle two, and maybe the one on the left is a boiler. Holding tanks there? No mash tun there right? or wrong? Did you order them in from the States?
From left to right....Brite Tank, Mash Tun, Hopback, Fermenter, Fermenter, Hot Liquor Tank, Boil Kettle. I ordered all of this from Stout Tanks & Kettles in Portland, OR.

Thanks a lot Canuck. I love the idea of the Brite tank, love the idea of all of it actually.

Post by **hebertovich** » Thu Aug 08, 2013 2:46 pm

Looks good!1 Send us another pic when you get them in the room, If they fit LOL and when you get the electronics and Pumps !

canuck · Post by **canuck** » Thu Aug 08, 2013 3:22 pm

I put my sink and 3 vessels in there just to give me an idea of how much space I'll have and where things will need to go. Of course I'd like it to be bigger, but it's gonna have to make due.

Post by **mr x** » Thu Aug 08, 2013 3:31 pm

I'm not sure how you plan to finish things, but I'd consider keeping that gyp-rock off the floor.

canuck · Post by **canuck** » Thu Aug 08, 2013 3:35 pm

mr x wrote:I'm not sure how you plan to finish things, but I'd consider keeping that gyp-rock off the floor.

It will be in the end, things aren't even remotely close to being finished at this point.

Post by **hebertovich** » Thu Aug 08, 2013 3:52 pm

canuck wrote:
mr x wrote:I'm not sure how you plan to finish things, but I'd consider keeping that gyp-rock off the floor.
It will be in the end, things aren't even remotely close to being finished at this point.

Are you tiling the floor? are you going to have a drain ?

dexter · Post by **dexter** » Thu Aug 08, 2013 3:55 pm

Stupid question but with the amount of steam that will likely be produced wouldn't a mold resistant drywall be a better idea?

canuck · Post by **canuck** » Thu Aug 08, 2013 4:19 pm

hebertovich wrote:
canuck wrote:
mr x wrote:I'm not sure how you plan to finish things, but I'd consider keeping that gyp-rock off the floor.
It will be in the end, things aren't even remotely close to being finished at this point.

Are you tiling the floor? are you going to have a drain ?

Yes to the drain, but the concrete floor will probably be painted instead of tiled. Walls will be tiled though.

canuck · Post by **canuck** » Thu Aug 08, 2013 4:20 pm

dexter wrote:Stupid question but with the amount of steam that will likely be produced wouldn't a mold resistant drywall be a better idea?

To meet fire regulations here and pass fire inspection, I needed to use 5/8" fire coded drywall to create a 1 hour separation from my brewery and the rest of my house.

NASH · Post by **NASH** » Thu Aug 08, 2013 6:26 pm

Looking awesome, brother! When do we start???

canuck · Post by **canuck** » Thu Aug 08, 2013 6:52 pm

NASH wrote:Looking awesome, brother! When do we start???

Realistically, I am hoping by the end of October. So.......what's our first collaborative brew?

canuck · Post by **canuck** » Wed Aug 28, 2013 2:19 pm

Control panel finally arrived today!

jeffsmith · Post by **jeffsmith** » Wed Aug 28, 2013 5:26 pm

stellfd28 · Post by **stellfd28** » Wed Aug 28, 2013 5:40 pm

Sweeeeett!!!!!

Sent from my iPhone using Tapatalk - now Free

Post by **mr x** » Wed Aug 28, 2013 5:52 pm

Very good!

GuingesRock · Post by **GuingesRock** » Wed Aug 28, 2013 6:10 pm

Is this in the trade section. I have a nice BIAB pot with a cooling coil. I'll throw in the car maybe too. Can we talk?

Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Re: Hammond River Brewing

Who is online