Page 1 of 1

Q re: Maxing out my mash Tun

Posted: Tue Sep 11, 2018 8:43 am
by weisseguy
So I’ve already used the Green Bay Rackers “Can I Mash it” calculator but I’m skeptical of the results so I wanted to double check with you guys.

What is the maximum amount of grain I can mash in an 11.7gal tun with 0.5gal dead space assuming 1.25 qt/lb mash thickness?

Also, what are the pros and cons of increasing the mash thickness? How thick is too thick?

As always, thanks in advance!


Sent from my iPhone using Tapatalk

Re: Q re: Maxing out my mash Tun

Posted: Tue Sep 11, 2018 12:54 pm
by mumblecrunch
weisseguy wrote:
Tue Sep 11, 2018 8:43 am

Also, what are the pros and cons of increasing the mash thickness? How thick is too thick?
Lots of good info about mash thickness and its effect on efficiency here: Braukaiser

Generally I think you'll find that it suggests thinner mashes tend to yield better efficiency. The caveat is that a maximally thin mash (e.g., no-sparge) loses about 7-8% efficiency. Thinner mashes are also less likely to produce dough balls.

If you're looking to do a really big beer with a manageable mash thickness to try to maximize efficiency you might be better off doing two smaller mashes or even experimenting with re-iterated mashing (I think a few members here have tried this with decent results, I just can't remember who).

If you're less concerned about efficiency and you just want to do a big beer in a single mash (minimize time spent), I've never seen anyone claim the "Can I Mash It" calculator was wrong.

Re: Q re: Maxing out my mash Tun

Posted: Tue Sep 11, 2018 1:31 pm
by weisseguy
mumblecrunch wrote:
weisseguy wrote:
Tue Sep 11, 2018 8:43 am

Also, what are the pros and cons of increasing the mash thickness? How thick is too thick?
Lots of good info about mash thickness and its effect on efficiency here: Braukaiser

Generally I think you'll find that it suggests thinner mashes tend to yield better efficiency. The caveat is that a maximally thin mash (e.g., no-sparge) loses about 7-8% efficiency. Thinner mashes are also less likely to produce dough balls.

If you're looking to do a really big beer with a manageable mash thickness to try to maximize efficiency you might be better off doing two smaller mashes or even experimenting with re-iterated mashing (I think a few members here have tried this with decent results, I just can't remember who).

If you're less concerned about efficiency and you just want to do a big beer in a single mash (minimize time spent), I've never seen anyone claim the "Can I Mash It" calculator was wrong.
All of this is fantastic info! Thank you very much!


Sent from my iPhone using Tapatalk

Re: Q re: Maxing out my mash Tun

Posted: Wed Sep 12, 2018 7:30 am
by McGruff
I use Green Bay Rackers the odd time and found it pretty accurate.

Re: Q re: Maxing out my mash Tun

Posted: Fri Sep 14, 2018 7:20 pm
by weisseguy
So I brewed a beer attempting to take my run to the brim and according to the GBR calculator I was maxing it out but in reality I had about 3 inches of space left. I realized three things:

1. I’m over estimating my dead space
2. I literally left out some malt my accident
3. I was slightly undershooting the total volumes anyway just to be safe.

Learning all this will be really helpful when I attempt new high gravity batches!

The end result of this will be two stouts. A RIS (est. ABV 9.5%) made from the combined 1st & 2nd runnings and another weakling (est. ABV 4%) from the 3rd runnings!

Thanks again for the support!
Cheers!




Sent from my iPhone using Tapatalk