Page 1 of 1
pin hole in my keg
Posted: Fri May 08, 2015 3:32 pm
by Halifax_Jeff
I cleaned and pressurized my kegs only to find that one of them had a leak. The pin hole is near the bottom of the keg but before where the rubber bottom is. I can't really see a physical hole, just a small knick. It is definitely leaking though I can feel air pushing out when I have the gas attached to it. Is this something I could easily fix?
I was thinking some sort of epoxy or something? Any help would be appreciated!
Re: pin hole in my keg
Posted: Fri May 08, 2015 5:14 pm
by LeafMan66_67
I have one with a pin hole, repaired with JB Weld. I only use it to hold and dispense Star San now.
Re: pin hole in my keg
Posted: Sat May 09, 2015 7:25 am
by Halifax_Jeff
Is that because you don't want to put too much pressure on it? Or because you have enough kegs to keep you going?
Re: pin hole in my keg
Posted: Sat May 09, 2015 7:36 am
by LeafMan66_67
Pressure isn't a problem, I've had it up at 30PSI (I pressurize and dispense star San with my compressor). I have enough kegs to keep me going without using this one. My pinhole was near the top, above the liquid line.
Re: pin hole in my keg
Posted: Sat May 09, 2015 2:02 pm
by mr x
I had a pinhole in one of mine that I silver soldered. There's pics here somewhere.
Re: pin hole in my keg
Posted: Sat Oct 31, 2015 6:36 am
by ibmman
have it welded with food grade stainless steel weld. Good as new
Re: pin hole in my keg
Posted: Sat Oct 31, 2015 10:12 am
by GAM
mr x wrote:I had a pinhole in one of mine that I silver soldered. There's pics here somewhere.
SS is my first thought. May be hard on a round surface.
Ball or pin lock? I may have one body I can trade you.
Sandy
Re: pin hole in my keg
Posted: Sat Oct 31, 2015 11:52 am
by Halifax_Jeff
GAM wrote:mr x wrote:I had a pinhole in one of mine that I silver soldered. There's pics here somewhere.
SS is my first thought. May be hard on a round surface.
Ball or pin lock? I may have one body I can trade you.
Sandy
It's a ball lock (single handle) but I already used some JB weld on it and its just been sitting in my basement I'm not sure if I should even use it for starsan... a little paranoid about it being in contact with it.
Re: pin hole in my keg
Posted: Sat Oct 31, 2015 1:34 pm
by GAM
Look for a MSDS sheet on JBW and see how inert it is cured.
S
Re: pin hole in my keg
Posted: Sat Oct 31, 2015 4:17 pm
by Halifax_Jeff
I took a quick look through the sheet but couldn't really find that info.. it's here if you know where you're looking for it
https://cdn.shopify.com/s/files/1/0411/ ... 1577326900" onclick="window.open(this.href);return false;
Re: pin hole in my keg
Posted: Sun Nov 01, 2015 9:57 am
by GAM
http://jbweldit.com.au/index.php?main_p ... ducts_id=9" onclick="window.open(this.href);return false;
J-B WELD is super strong, non-toxic, and safe to use. Before it sets, you can clean up with soap and water
You can also e-mail/call them and ask.
S
Re: pin hole in my keg
Posted: Sun Nov 01, 2015 6:13 pm
by Halifax_Jeff