Morning folks...I have a question that's been bugging me, but never think to ask.
I'm interested to know how intense of a boil you all keep on your brew days. Does boil intensity have an affect on the final out come or just evaporation rates?
I've recently started doing 40L-ish batches in my keggle and that doesn't leave a lot of room at the very top. As hard as I try, hotbreak boil overs have become a relatively normal thing. Though I fight it hard as I hate a sticky garage floor. Then if its a heavy rolling boil, I still get a fair bit of splashing.
Which leads me to another question now that I think of it. When do you all start your clock for your boil time? After hot break is basically over?
I think I brew a little too haphazardly most days to get this part of my process dialed in (heavy vs light boil) . I haven't had to dump a batch yet...so its more just a general interest 'whats everyone else doing' kinda question.
ok...ler 'er rip....
Boil intensity
- sgrhyno
- Verified User
- Posts: 146
- Joined: Thu Mar 10, 2016 12:20 pm
- Name: Shaun Rhyno
- Location: Lewis Lake
- jacinthebox
- Award Winner 16
- Posts: 3047
- Joined: Tue Oct 16, 2012 12:44 pm
- Name: Justin
- Location: Hubley
- Contact:
Re: Boil intensity
I have mine on full tilt (propane)...only because I know the boil off when it's on blast with wind blocker
Brathair Brewing
Brew Hard...Stay Humble
Brew Hard...Stay Humble
- mckay75
- Award Winner 6
- Posts: 750
- Joined: Tue Feb 14, 2012 5:36 pm
- Name: Mark
- Location: Truro
- Contact:
Re: Boil intensity
Invest in some Fermcap and never worry about a boil over again.
I run a pretty vigorous boil...I use one the Stilldragon DIY electric controllers and am prob running it at 85% throughout the whole boil. It's at 100% until the hotbreak finishes.
I run a pretty vigorous boil...I use one the Stilldragon DIY electric controllers and am prob running it at 85% throughout the whole boil. It's at 100% until the hotbreak finishes.
- CartoonCod
- Award Winner 1
- Posts: 858
- Joined: Wed Oct 06, 2010 9:39 am
- Name: Adam Comeau
- Location: Halifax
Re: Boil intensity
When I was brewing with propane I could set it as low as it could go, just enough to see the wort overturn, mostly to save on propane.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
- sgrhyno
- Verified User
- Posts: 146
- Joined: Thu Mar 10, 2016 12:20 pm
- Name: Shaun Rhyno
- Location: Lewis Lake
Re: Boil intensity
Thanks guys! I use propane too, hoping one day to go electric. I tend to turn mine down too once I hit a boil to manage the hotbreak and stop the spills. I've been missing my numbers since I started the 10 gal batchs and now I think it might be due to my lower intensity boil (less than expected evap).
My take aways
1. fermcap. I'm getting some
2. boil intensity doesn't seem to matter as much as dialing in your evap rate...
Time for some more experiments.
My take aways
1. fermcap. I'm getting some
2. boil intensity doesn't seem to matter as much as dialing in your evap rate...
Time for some more experiments.
- GAM
- Verified User
- Posts: 5403
- Joined: Wed May 18, 2011 2:50 pm
- Name: Sandy MacNeil
- Location: North End HFX
Re: Boil intensity
The evap rate is effected by exposed surface area not volume. Beersmith is a good tool to estimate the loss.
Also I use Fermcap all the time.
S
Also I use Fermcap all the time.
S
- sgrhyno
- Verified User
- Posts: 146
- Joined: Thu Mar 10, 2016 12:20 pm
- Name: Shaun Rhyno
- Location: Lewis Lake
Re: Boil intensity
Yeah...I use beer smith pretty much exclusively. The only reason I was relating my evap rate to volume was because I could run my 5gal batch’s at a much more vigour boil, so I was likely getting more evap loses.
Brewed this weekend and am definitely getting some fermcap. Garage floor is still sticky...
Sent from my iPhone using Tapatalk
Brewed this weekend and am definitely getting some fermcap. Garage floor is still sticky...
Sent from my iPhone using Tapatalk
Who is online
Users browsing this forum: No registered users and 41 guests